
RE-11 1953-66 fender panel buffers for under the removable fender panels. Requires 5 per side, sold as a set of 10.
$39.00
$39.00

RE-4 1953-66 fender panel hardware kit. 8 screws, 8 clips, and 8 crimped washers. Enough to attach both fender panels.
$95.00 Kit.
$95.00 Kit.

RE-88 1953-66 hood lace material and clips. This is the material on the cowl and on the radiator shell that the hood comes to rest on. You get a section of lace material 11 feet long, and 30 T clips. This is enough to do the standard 1953-66 cab.
$179.00 Set.
$179.00 Set.

RE-82 Hoodlace T clips only. A bag of 30 clips used to attach the hoodlace material onto the cowl area and onto the radiator shell.
$34.00 Bag.
$34.00 Bag.

RE-38 1953-66 fender welt. This is the material used at the rear of the fender, between the fender and the hood. There is a quarter round bead along the edge of the material that acts as a seal. This 10 foot strip is enough to do both fenders.
$58.00 Strip.
$58.00 Strip.

RE-37 1953-66 fender panel clips. These attach to the fender to attach the fender panels. 8 per truck required.
$4.00 Each.
$4.00 Each.

RE-94 1953-66 clips for attaching the hood trim strips. These are a good quality aftermarket clip with a foam packing to help create a tighter fit. 14 required per truck.
$13.00 Set.
$13.00 Set.

RE-4243 1953-66 hood hinge endcap set. You get 2 endcaps and 2 securing strips, for a total of 4 pieces. These work on other truck models, as well as Durant automobiles.
$107.00 Set.
$107.00 Set.

RE-12 1953-66 hood hinge and endcap set. Includes center hood hinge, 2 endcaps, and 2 securing strips for the underside. Hinge is about 56 3/4'' long, and may need cut down to fit your truck. There is currently a problem with availibility, please email me for current status and pricing. The hinges that I have are all new old stock. They will need cleaned and polished, as they were stored for many years in an open crate without any wrapping. Once this supply is gone, there may not be any more to be found.
Pricing is as follows. Hinge only---$265
Endcaps only----$107
Hinge and endcap set $372
Pricing is as follows. Hinge only---$265
Endcaps only----$107
Hinge and endcap set $372

RE-8 1953-66 replacement hood hinge channels. Each is about 59 3/4 long, they get spotwelded to the hood sections to allow the slide on hinge to be put into place. Very limited quantity available, will probably never be available again. Now is the chance to strengthen your hood with the proper channel piece.
$36.00 Pair.
NOTE: some strips will have some light surface rust.
$36.00 Pair.
NOTE: some strips will have some light surface rust.

RE-24 1953-66 welt used on the front fender seam, and between the radiator shell and headlight panel. This welting has a raised bead encased in a vinyl sheeting. This 16' strip will do both sides. Please measure carefully before cutting.
Not currently available--I now offer an aftermarket welt that is just slightly narrower, it is solid rubber rather than the vinyl clad welt. A 16 foot piece will do both sides. I have had no issues with these thus far.
$48.00 for 16' section
Not currently available--I now offer an aftermarket welt that is just slightly narrower, it is solid rubber rather than the vinyl clad welt. A 16 foot piece will do both sides. I have had no issues with these thus far.
$48.00 for 16' section

NOW AVAILABLE AGAIN
RE-5 Replacement hood latch buffers. These work on the 1953-66 and onward models. You get a set of 4 exactly as shown. I have a good supply available.
$31.00 for a set of 4.
RE-5 Replacement hood latch buffers. These work on the 1953-66 and onward models. You get a set of 4 exactly as shown. I have a good supply available.
$31.00 for a set of 4.